Windows 7 Loader 1 7
What I think has happened: Windows 7 installed first and badly. I installed it again. First, there was Windows XP to guide where the bootloader went to so it was put on /dev/sdb1/. But, the second time no such guide existed so the machine put another bootloader on /dev/sda1/. sda1, by the way, is the only partition on a 2TB drive. No boot record partition appears to exist according to gedit. I'm not sure where Grub2 is getting this information from. But, there it is.
Windows 7 loader 1 7
The taskbar has seen the biggest visual changes, where the old Quick Launch toolbar has been replaced with the ability to pin applications to the taskbar. Buttons for pinned applications are integrated with the task buttons. These buttons also enable Jump Lists to allow easy access to common tasks, and files frequently used with specific applications. The revamped taskbar also allows the reordering of taskbar buttons. To the far right of the system clock is a small rectangular button that serves as the Show desktop icon. By default, hovering over this button makes all visible windows transparent for a quick look at the desktop. In touch-enabled displays such as touch screens, tablet PCs, etc., this button is slightly (8 pixels) wider in order to accommodate being pressed by a finger. Clicking this button minimizes all windows, and clicking it a second time restores them.
Window management in Windows 7 has several new features: Aero Snap maximizes a window when it is dragged to the top, left, or right of the screen. Dragging windows to the left or right edges of the screen allows users to snap software windows to either side of the screen, such that the windows take up half the screen. When a user moves windows that were snapped or maximized using Snap, the system restores their previous state. Snap functions can also be triggered with keyboard shortcuts. Aero Shake hides all inactive windows when the active window's title bar is dragged back and forth rapidly.
We had a SATA3 drive that was performing poorly and making noise, and installed Windows 7 onto a new drive. The install went well, but left the bootloader on the old drive, and so I could not remove it; Windows treated it as a multi-boot system with a new boot option on the new disk. Everything worked, so I figured I'd have time to fix it. Well, the old drive died a few weeks later and now I have no idea how to address this.
How can I instruct the PC to boot to the new disk, when there isn't a bootloader present on it? Do I need to reinstall Windows from scratch? From looking at the board specs, it supports UEFI, I am unsure if this is relevant.
In particular, this message indicates that Startup Repair was unable to find the correct BOOTMGR bootloader at the expected location(s). While the usual fix for a missing bootloader is to run Startup Repair, in this case, Startup Repair is unable to correct the problem for one or more reasons.
Note: If your PC starts to load Windows, but then fails, then the bootloader is not the problem. Instead, you should try starting the PC in Safe Mode and troubleshooting from there. Performing a System Restore would be a good place to start.
However, this should not concern you. The installation can be performed in an offline mode if you will,especially the tricky parts of configuring the partitions and the bootloader. The post-install use is anothermatter, but provided you selected a machine that works well in Linux, you will be absolutely fine. So please,IGNORE the Wireless woes, they are totally unrelated, and focus on the mechanics of dual booting.
The first two steps are as follows: Choose your language. Then, take a look at the summary window. It willhighlight steps that need completion before you can move on to the next stage. In this case, the tricky part iscalled Installation Destination. What it actually means is that you will need to prepare your disks, mark yourpartitions and configure the bootloader.
The third section, named, Other Storage Options is the most critical one. We will not opt for the automaticpartitioning, because it could be destructive. Instead, we will configure partitions manually. Mark therelevant radio button. Encryption is not important at this point. At the bottom, the blue hyperlink will takeyou to the bootloader setup. You can do that right now, but your choice will be reset if you change the deviceselection and choose some of the partitions.
Therefore, you should mark the right disks, click Done, manually partition, come back to this window, reviewthe bootloader selection, and finally hit the Done button again. This is meant to be some kind of a star-logicnon-linear installation flow, and it's quite confusing. Pay attention.
After you've completed this, click Done. This will take you back to the previous menu, where we will now makesure the bootloader has been marked for installation and properly configured to the MBR